View TLP116A_4629669.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TLP116A
TOSHIBA PHOTOCOUPLER GaAAs LED & PHOTO-IC
TLP116A
Plasma Display Panels (PDPs) High-Speed Interface Factory Automation (FA)
The Toshiba TLP116A mini-flat coupler is a small-outline coupler suitable for surface-mount assembly. The TLP116A consists of a GaAAs light-emitting diode and an integrated high-gain, high-speed photodetector. This unit is housed in the 6-pin SO package and guarantees a creepage distance of 5.0mm, a clearance of 5.0mm and an insulation thickness of 0.4mm. Therefore, the TLP116A meets the reinforced insulation class requirements of international safety standards. Unit: mm
6 5 4
1
3 7.0 0.4 0.1 2.1 0.1
3.7 0.15
4.55 0.15 0.4 0.15
0.5 min
Inverter logic (totem-pole output) SO6 package Guaranteed performance over: -40 to 100C Power supply voltage: 4.5 to 5.5V Input thresholds current: IFHL = 5 mA (max) Propagation delay time (tpHL / tpLH): 60 ns (max) Switching speed: 20 MBd (typ.) Common-mode transient immunity: 10 kV/us Isolation voltage: 3750 Vrms UL approval: UL1577, File No.E67349 Under application
1.27 2.54
TOSHIBA 114L1 Weight: 0.08 g (typ.)
Truth Table
Input H L LED ON OFF Tr1 OFF ON Tr2 ON OFF Output L H
Pin Configuration (Top View)
1
VCC
6 5
1: ANODE 3: CATHODE 4: GND 5: VO (Output) 6: VCC
Construction Mechanical Rating Creepage Distance: 5.0mm (min) Clearance: 5.0mm (min) Insulation Thickness: 0.4mm (min)
3
GND SHIELD
4
Schematic
IF 1+ VF 3 Tr2 Tr1
ICC 6 VCC
IO VO 5
4 SHIELD A bypass capacitor of 0.1F must be connected between pins 6 and 4.
GND
1
2008-10-01
TLP116A
Absolute Maximum Ratings (Ta=25C)
Characteristic
Forward current LED Forward current derating (Ta 85C) (Note 1) Symbol IF IF / Ta IFPT VR IO VO VCC PO Topr Tstg Tsol (Note 2) BVs Rating 20 -0.5 1 5 10 6 6 40 -40 to 100 -55 to 125 260 3750 Unit mA mA/C A V mA V V mW C C C Vrms
Peak transient forward current Reverse voltage
DETECTOR
Output current Output voltage Supply voltage Output power dissipation
Operating temperature range Storage temperature range Lead solder temperature(10 s) Isolation voltage (AC,1 min.,R.H. 60%,Ta=25C)
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook ("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test report and estimated failure rate, etc).
Recommended Operating Conditions
Characteristic Input current , ON Input voltage , OFF Supply voltage Operating temperature (Note 3) Symbol IF(ON) VF(OFF) VCC Topr Min 8 0 4.5 -40 Typ. Max 18 0.8 5.5 100 Unit mA V V C
-- --
5.0 --
Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document.
Correlation between Input current, switching speed and drive circuit (reference information).
Input current (IF) 12mA 8mA 8mA Test Circuit 1 (Page 4) 1 (Page 4) 2 (Page 4, With Speed up capacitor) Typical switching speed 21 - 23 MBd 18 - 20 MBd 23 - 27 MBd
Note 1 : Pulse width PW 1s, 300 pps. Note 2 : This device is regarded as a two terminal device : pins 1 and 3 are shorted together, as are pins 4,5 and 6. Note 3 : The detector of this product requires a power supply voltage (VCC) of 4.5 V or higher for stable operation. If the VCC is lower than this value, an ICC may increase, or an output may be unstable. Be sure to use the product after checking the supply current, and the operation of a power-on/-off.
2
2008-10-01
TLP116A
Electrical Characteristics (Unless otherwise specified, Ta=-40 to 100C, VCC=4.5 to 5.5 V )
Characteristic Input forward voltage Temperature coefficient of forward voltage Input reverse current Input capacitance Logic low output voltage Logic high output voltage Symbol VF VF /Ta IR CT VOL VOH ICCL ICCH IFHL VFLH Test Circuit Conditions IF = 10 mA ,Ta = 25C IF = 10 mA VR=5 V, Ta = 25C V = 0, f= 1 MHz, Ta = 25C IOL = 1.6 mA, IF = 12 mA, VCC = 5 V IOH = -0.02 mA, VF = 1.05 V, VCC = 5 V IF = 12 mA VF = 0 V IO = 1.6 mA, VO < 0.4 V IO = -0.02 mA, VO > 4.0 V Min 1.45 Typ. 1.58 -2.0 Max 1.85 Unit V mV/C A pF V V
-- -- -- --
1 2
-- -- -- --
4.0
--
10
--
60
--
0.4
-- -- -- -- -- --
--
5.0 5.0 5
Logic low supply current Logic high supply current Input current logic low output Input voltage logic high output
3 4
-- -- --
0.8
mA mA mA V
-- --
--
*All typical values are at Ta=25C, VCC=5 V, IF(ON)=12 mA unless otherwise specified
Isolation Characteristics (Ta = 25C)
Characteristic Capacitance input to output Isolation resistance Symbol CS RS Test Conditions Vs = 0,f = 1 MHz R.H. 60%, VS = 500 V AC,1 minute Isolation voltage BVS AC,1 second,in oil DC,1 minute,in oil (Note 2) Min 1x10
12
Typ. 0.8 10
14
Max
Unit pF Vrms Vdc
(Note 2)
3750
10000 10000
Note 4:A ceramic capacitor(0.1 F) should be connected from pin 6 to pin 4 to stabilize the operation of the high gain linear amplifier. Failure to provide the bypass may impair the switching property. The total lead length between capacitor and coupler should not exceed 1 cm.
3
2008-10-01
TLP116A
Switching Characteristics (Unless otherwise specified, Ta=-40 to 100C, VCC=4.5 to 5.5 V)
Characteristic
Propagation delay time to logic high output Propagation delay time to logic low output Propagation delay time to logic high output Propagation delay time to logic low output Switching time dispersion between ON and OFF Output fall time(90-10%) Output rise time(10-90%) Common mode transient immunity at high Level output Common mode transient immunity at low level output *All typical values are at Ta=25C Note 5: CL is approximately 15 pF which includes probe and Jig/stray wiring capacitance. CML CMH 7 VCM = 1000 Vp-p, IF = 12 mA, Vo(Max) = 0.4 V, Ta = 25C -10000 Symbol tpHL 5 tpLH tpHL 6 tpLH |tpHLtpLH| tf 5 IF = 120 mA VIN = 05 V (IF = 08 mA) VIN = 50 V (IF = 80 mA) Test Circuit Conditions IF = 012 mA RIN = 100 CL = 15 pF (Note 5) RIN = 470 CIN = 27 pF CL = 15 pF (Note 5) Min. Typ. Max. 60 60 60 60 30 Unit ns ns ns ns
-- -- -- -- -- -- --
-- -- -- -- --
15 15
IF = 12 mA , RIN = 100 , CL =v15 pF (Note 5) IF = 012 mA IF = 120 mA RIN = 100 CL = 15 pF (Note 5)
ns ns ns
-- -- --
tr
VCM = 1000 Vp-p, IF = 0 mA, Vo(Min) = 4 V, Ta = 25C
10000
--
V/s
--
--
V/s
TEST CIRCUIT 1: VOL
IF
TEST CIRCUIT 2: VOH
6 VCC 5
0.1 F
1
1
6 VCC 5
V
VOH
IOH VCC
3 SHIELD
GND 4
VOL
V
IOL
VCC 3 SHIELD GND 4
0.1 F
TEST CIRCUIT 3: ICCL
IF 1
6 VCC 5 3 SHIELD 4 ICCL
A
0.1 F
TEST CIRCUIT 4: ICCH
1 VCC 6 5 3 SHIELD 4 ICCH
A
0.1 F
VCC GND
VCC
GND
4
2008-10-01
TLP116A
TEST CIRCUIT 5: tpHL, tpLH
IF = 12 mA(P.G)
(f = 5 MHz , duty = 50% less than tr = tf = 5 ns)
VCC 0.1 F
INPUT MONITORING NODE Vo MONITORING NODE
50%
IF
VCC
VO
tf
tr
90% OH
V
GND CL=15 pF SHIELD RIN=100
CL = 15 pF 1.5 V tpHL tpLH
10%
VOL
CL is capacitance of the probe and JIG. (P.G): Pulse Generator
TEST CIRCUIT 6: tpHL, tpLH
VIN = 5 V(P.G)
(f = 5 MHz , duty = 50% less than tr = tf = 5 ns)
INPUT MONITORING NODE
VCC 0.1 F
Vo MONITORING NODE
CL=15 pF
50%
IF
VCC
GND SHIELD CIN=27 pF RIN=470
CL=15 pF
VO
tf
tr
90% OH
V
1.5 V CL is capacitance of the probe and JIG. (P.G): Pulse Generator tpHL tpLH
10%
VOL
TEST CIRCUIT 7: Common-Mode Transient Immunity Test Circuit
90% SW A B 3 SHIELD VCM SW A : IF=5 mA 1000 V
IF
1
6 VCC 5 GND 4 0.1 VO VCC SW B : IF=0 mA 4V 0.4 V CML CMH 10% tr tf
CM
H
=
800(V ) t r (s)
CM
L
=
800(V ) t f ( s)
5
2008-10-01
TLP116A
Specification for Embossed-Tape Packing (TPL)(TPR) for SO6 Coupler
1. Applicable Package
Package SO6 Product Type Mini-flat coupler
2. Product Naming System
Type of package used for shipment is denoted by a symbol suffix after a product number. The method of classification is as below. (Example)
TLP116A(TPL) Tape type Device name
3. Tape Dimensions
3.1 Specification Classification Are as Shown in Table 1 Table 1 Tape Type Classification
Tape type TPL TPR Classification L direction R direction Quantity (pcs/reel) 3000 3000
3.2 Orientation of Device in Relation to Direction of Tape Movement
Device orientation in the recesses is as shown in Figure 1.
Direction of Tape
L direction
R direction
Figure 1 Device Orientation
6
2008-10-01
TLP116A
3.3 Empty Device Recesses Are as Shown in Table 2. Table 2 Empty Device Recesses
Standard Occurrences of 2 or more successive empty device recesses Single empty device recesses Remarks Within any given 40-mm section of tape, not including leader and trailer Not including leader and trailer
0
6 devices (max.) per reel
3.4 Start and End of Tape
The start of the tape has 50 or more empty holes. The end of tape has 50 or more empty holes and two empty turns only for a cover tape.
3.5 Tape Specification
(1) Tape material: Plastic (protection against electrostatics) (2) Dimensions: The tape dimensions are as shown in Figure 2 and Table 3.
0.3 0.05 +0.1 1.5 -0 G A E K0 1.6 0.1 3.15 0.2 F
Figure 2 Tape Forms Table 3 Tape Dimensions
Unit: mm Unless otherwise specified: 0.1 Symbol A B D E F G K0 Dimension 4.2 7.6 5.5 1.75 8.0 4.0 2.8 Remark Center line of indented square hole and sprocket hole Distance between tape edge and hole center +0.1 Cumulative error -0.3 (max) per 10 feed holes Cumulative error +0.1 (max) per 10 feed holes -0.3 Internal space
7
12.0 0.3
B
D
2008-10-01
TLP116A
3.6 Reel
(1) Material: Plastic (2) Dimensions: The reel dimensions are as shown in Figure 3 and Table 4.
C
U E
B
W1 W2
Figure 3 Reel Form Table 4 Reel Dimensions
Unit: mm Symbol A B C E U W1 W2 Dimension 380 2 80 1 13 0.5 2.0 0.5 4.0 0.5 13.5 0.5 17.5 1.0
4. Packing
Either one reel or five reels of photocoupler are packed in a shipping carton.
5. Label Indication
The carton bears a label indicating the product number, the symbol representing classification of standard, the quantity, the lot number and the Toshiba company name.
6. Ordering Method
When placing an order, please specify the product number, the tape type and the quantity as shown in the following example. (Example)
TLP116A (TPL) 3000 pcs Quantity (must be a multiple of 3000) Tape type Device name
8
A
2008-10-01
TLP116A
RESTRICTIONS ON PRODUCT USE
* Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice. * This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission. * Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily injury or damage to property, including data loss or corruption. Before creating and producing designs and using, customers must also refer to and comply with (a) the latest versions of all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes for Product and the precautions and conditions set forth in the "TOSHIBA Semiconductor Reliability Handbook" and (b) the instructions for the application that Product will be used with or for. Customers are solely responsible for all aspects of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS' PRODUCT DESIGN OR APPLICATIONS. * Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document. Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious public impact ("Unintended Use"). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this document. * Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part. * Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. * The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. * ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT. * GaAs (Gallium Arsenide) is used in Product. GaAs is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. Handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose GaAs in Product. * Do not use or otherwise make available Product or related software or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technology products (mass destruction weapons). Product and related software and technology may be controlled under the Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations. * Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations.
9
2008-10-01

▲Up To Search▲

Price & Availability of TLP116A

	To Download TLP116A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .